![]() ![]() Releasing the mouse button again stops moving bends. This will move all selected bends along with the mouse cursor. Then start left-dragging the mouse on one of the selected bends. To deselect all bends click on an unoccupied location in the editor.įirst select the bends that you want to move. Either click on a bend or select multiple bends by opening up a selection box with or without the SHIFT key held down. See also: Orthogonal Edges, Snap Lines Selecting and deselecting bendsīends are selected the same way as nodes. This will insert a new bend on that edge at the pressed location and moves the bend along with the mouse cursor. Start left-dragging the mouse on an edge. See also: Add/Remove a node to a group node/from a group node, Orthogonal Edges, Snap Lines Creating bends The nodes will stop moving when the mouse button is released. The selected nodes will now move along with the mouse cursor. Then press the left mouse button over one of the selected nodes and start dragging the mouse. Moving nodes Select the nodes that you want to move around. To deselect all edges click on an unoccupied location in the editor. To select all edges, first select one edge then trigger the select all action by hitting CTRL-A. Selecting more than one edge requires two steps: first select one edge as described above, then open up a selection box with the SHIFT key held down to add more edges to the selection. See also: Create a new edge that connects to a group node, Orthogonal Edges Selecting and deselecting edges Alternatively, use the ESC key to cancel edge creation.Īn edge can also be created by dragging a sample edge representation from the Palette tool window onto a node in the active editor window (using a mouse drag gesture). By left-clicking on an end node, the edge with additional bends will be created.īy clicking the right mouse button the edge or bend creation will be canceled. More bends can be created by clicking with the left mouse button on an unoccupied location. If the mouse is not released over a node, a control point (also called bend) for the new edge will be inserted at that release location. Then release the mouse button over an end node. Start left-dragging the mouse from an unselected start node. See also: Selecting group nodes, Selecting covered elements and internal node labels Creating a new edge The selection state of all other nodes remains as it was. If it was already selected it is deselected. Opening up a selection box with the SHIFT key held down adds the selection box nodes to the set of previously selected nodes.Ĭlicking on a node with the SHIFT key held down selects the node, if it was not already selected. All objects outside the box will be deselected. Releasing the mouse button will select all nodes that lie within the selection box. Click on any location in the editor not occupied by a node to deselect all nodes.īy left-dragging the mouse, starting from an unoccupied location in the editor, a selection box will open up.īy dragging the mouse around one can change the bounds of the box. A selected node will have a different appearance than an unselected one. See also: Create a new group node, Add/Remove a node to a group node/from a group node Selecting and deselecting nodesĬlick on a node to select it. If there are selected graph elements, then no node will be created but the graph elements are deselected instead. The mouse click must occur at an empty place within the drawing canvas. A new default node will appear at that spot. The new node is created at the drop location.Īdditionally, it is possible to create a node by a simple mouse click (left mouse button) within the active editor window if optionĬreate Node on Background Click is enabled. Image nodes can also be created by dragging an image file from the file system onto the active editor. The following actions can be performed by using the mouse or the keyboard:Ī node can be created by dragging any of the sample node representations from the Palette tool window into the active editor window (using a mouse drag gesture). This mode allows for creating and/or manipulating a graph that is shown in the editor. The following describes the behavior of the edit mode, if these additional features are switched off. They can be switched on or off from the tool bar and the menu bar. ![]() There are three optional features which have an influence on how the Edit Mode works: Snap Lines, Grid and Orthogonal Edges. When yEd starts up, it is in Edit Mode by default. Either of these modes can be activated from the tool bar and the menu bar. The Edit Mode supports creation of a graph and its elements and allows all kinds of modifications to them.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |